background image

 

 

necessary revision to the product from time to time due to the reason of 
sales or production, and reserve the right to revise the contents without 
further notice. 

(7)  Indoor unit must not be installed in a laundry. 
(8)  If the supply cord is damaged, it must be replaced by the manufacturer, its 

service agent or similarly qualified persons in order to avoid a hazard. 

(9)  Gree Electric Appliances Inc. of Zhuhai assumes no responsibility for 

personal injury, property loss or equipment damage caused by improper 
installation and commissioning, unnecessary maintenance, or not 
following relevant national rules and regulations, industrial standards and 
requirements in this instruction manual. 

(10) The final right to interpret  for this instruction manual belongs to Gree 

Electric Appliances Inc. of Zhuhai. 

 

Exception Clauses 

Manufacturer will bear no responsibilities when personal injury or property loss 

is caused by the following reasons: 

(1)  Damage the product due to improper use or misuse of the product; 
(2)  Alter, change, maintain or use the product with other equipment without 

abiding by the instruction manual of manufacturer; 

(3)  After verification, the defect of product is directly caused by corrosive gas; 
(4)  After verification, defects are due to improper operation during 

transportation of product; 

(5)  Operate, repair, maintain the unit without abiding by instruction manual or 

related regulations; 

(6)  After verification, the problem or dispute is caused by the quality 

specification or performance of parts and components that produced by 
other manufacturers; 

(7)  The damage is caused by natural calamities, bad using environment or 

force majeure. 

Summary of Contents for U-Match GU100T/A1-K























































Reviews: