Gree GWH12QB-K3DNA5D Page 65 Service Manual Download

Page: 65 / 114

Installation and Maintenance

Service Manual

Indoor ambient
temperature
sensor is open/
short- circuited

The unit will stop operation
as it reaches the temperature
point. During cooling and drying
operation, compressor and
outdoor unit stop, while indoor
fan operates; During heating
operation, the complete unit
stops operation.

Connection terminal
between indoor ambient
temperature sensor and
main board is loose or
poor connection.

Refer to maintenance
flowchart

Theres short circuit due
to trip-over of the parts
on main board;

Indoor ambient
temperature sensor
is damaged (Please
check it by referring to
the resistance table for
temperature sensor)

Main board is
damaged.

Indoor
evaporator
temperature
sensor is open/
short-circuited

Connection terminal
between indoor
evaporator temperature
sensor and main
board is loose or poor
connection.

Refer to maintenance
flowchart

Theres short circuit due
to trip-over of the parts
on main board;

Indoor evaporator
temperature sensor
is damaged (Please
check it by referring to
the resistance table for
temperature sensor)

Main board is
damaged.

Summary of Contents for GWH12QB-K3DNA5D



















































































































Search results

Summary of Contents for GWH12QB-K3DNA5D

Reviews:

Related manuals for GWH12QB-K3DNA5D

Brands by name

Popular brands

Gree GWH12QB-K3DNA5D, Service Manual

Search results

Summary of Contents for GWH12QB-K3DNA5D

Reviews:

Related manuals for GWH12QB-K3DNA5D

Brands by name

Popular brands