Gree GWH09MA-K3DNA3L Service Manual Download

Page: 71 / 89

Installation and Maintenance

Service Manual

Open the front panel; separate the panel
rotation shaft from the groove fixing the
front panel and then removes the front
panel.

Note:
The display of some models is fixed on
the panel; unscrew the screws fi xing the
display on the panel before removing the

panel.

Remove the screws on the electric box
cover 2 to remove the electric box cover 2.

Electric box cover 2

Screws

Panel

Front panel

Panel rotation

Groove

3. Remove panel

4. Remove electric box cover 2

Front case

sub-assy

Front case
sub-assy

Left clasp

Middle clasp Right clasp

Screw caps

Screws

Remove the screws fi xing front case.

Note:
1.Open the screw caps before removing
the screws around the air outlet.
2.The quantity of screws fixing the front
case sub-assy is different for different
models.

Loosen the clasps at left, middle and right
sides of front case. Life the front case
sub-assy upwards to remove it.

5. Remove front case sub-assy

Procedure

Steps

Summary of Contents for GWH09MA-K3DNA3L


























































































Search results

Summary of Contents for GWH09MA-K3DNA3L

Reviews:

Related manuals for GWH09MA-K3DNA3L

Brands by name

Popular brands

Gree GWH09MA-K3DNA3L, Service Manual

Search results

Summary of Contents for GWH09MA-K3DNA3L

Reviews:

Related manuals for GWH09MA-K3DNA3L

Brands by name

Popular brands