background image

  Air Source Heat Pump Water Heater

 

  Water inlet of water tank must install safety valve as required;

 

  Try to use tap water, avoid not using well water or river water;

 

  To guarantee water quality, clean the water tank periodically as required; 

  Water tank shall be installed in places without rainwater. If not, take 

rain-proof measures. 

 

NO. 

Safety Notices 

Graphic symbol 

 Once abnormality like burning smell occurs, 

please cut off the power supply immediately and 

then contact with service center. 

If the abnormality still exists, the unit may be 

damaged and electric shock or fire may result. 

 

 Don't operate water heater with wet hand. 

Otherwise, it may cause electric shock. 

 

 Before installation, please see if the voltage of 

local place accords with that on nameplate of unit 

and capacity of power supply, power cord or socket 

is suitable for input power of this unit. 

 

 Special circuit must be adopted for power supply 

to prevent fire. 

Do not use octopus multipurpose plug or mobile 

terminal board for wire connection. 

 

 Be sure to pull out the power plug and drain the 

main unit and water tank when water heater is not in 

use for a long time. 

Otherwise, the accumulated dust may cause 

overheating, fire or freeze of water tank or coaxial 

heater exchanger in winter. 

 

 Never damage the electric wire or use the one 

which is not specified. 

Otherwise, it may cause overheating or fire. 

 

Summary of Contents for GRS-1.5/TD150ANbA-K







































Reviews: