Gree GMV-ND28TS/B-T Owner'S Manual Download Page 6

Multi Variable Air Conditioners Two-way Cassette Type Indoor Unit

 

 

Please use specialized 
accessories or parts to 
carry out installation, or 
water leakage, electric 
shock, fire hazard may 
resulted. 

 

R410A refrigerant can 
produce poisonous gas 
once it meets fire, so 
please ventilate the room 
immediately if refrigerant 
leaks out during 
installation. 

 

Diameter of power cord 
must be large enough. 
Damaged power cord and 
connecting wire must be 
replaced by specialized 
electric cable. 

 

After the power cord is 
connected, please install 
the cover of electric box to 
avoid danger. 

 

Nitrogen must be charged 
according to technical 
requirements. 

 

Short circuit is forbidden. 
Do not cancel the pressure 
switch in case the unit may 
be damaged.   

 

For units with wired 
controller, do not connect 
power supply until the 
wired controller is well 
installed. Otherwise, the 
wired controller cannot be 
used. 

 

When the installation is 
finished, please check and 
make sure the drain pipe, 
pipeline and electric wire 
are all well connected in 
order to avoid water 
leakage, refrigerant 
leakage, electric shock or 
fire hazard. 

 

Do not extend fingers or 
objects into air outlet or air 
return grille. 

 

If you use gas heater or 
petroleum heater in the 
same room, please open 
the door or window to 
maintain good air 
circulation in case the 
room may lack of oxygen. 

 

Never start or stop the air 
conditioner by inserting or 
removing the power cord. 

 

Do not turn off the air 
conditioner until it runs for 
at least 5 minutes. 
Otherwise, oil-return of the 
compressor will be 
affected. 

 

Children are not allowed to 
operate the air conditioner. 

 

Do not operate the air 
conditioner with wet 
hands. 

Summary of Contents for GMV-ND28TS/B-T





























Reviews: