background image

8

Energy-Recovery Ventilation 

System Service Manual

CONTROL

2 MAIN LOGIC

2.1 Auto Mode 

Detect the temperature indoor and outdoor for durative a period of time.
(1) The system will operate under by pass mode according to temperature and temperature difference between room and 

outdoors is little in transient season.

The system will operate as such request:

By Pass air valve opens, the air discharge fan and air supply fan will operate according to setting fan speed.
(2) The system will operate under heat exchange mode according to temperature and temperature difference between 

room and outdoors is large in transient season.

The system will operate as such request:

By Pass air valve closes, the air discharge fan and air supply fan will operate according to setting fan speed.
(3) The system will operate according to the primary mode before the system was off.

2.2 By-pass Mode 

(1) Under By pass mode, air valve is open.
(2) 

The system will operate as such request:

If the air valve is close, the air discharge fan and air supply fan will stop. When the air valve is open , the fan will operate 

according to setting fan speed.

2.3 Heat exchange Mode

(1) Under Heat Exchange mode, the air valve is close.
(2) 

The system will operate as such request:

Electrify the air valve motor, judge the position of the air valve. The air discharge fan and air supply fan will stop if the air 

valve is open, or they will operate according to setting fan speed.

3 WIRED REMOTE CONTROLLER

3.1 Operation View

Fig.1 Front panel of wired controller

Timing set point 

10 

Mode key 

Energy saving status 

11 

Humidity increasing key 

Humidity set point 

12 

Humidity decreasing key 

Environment temperature 

13 

Fan speed key 

Air mode status (fresh air, 

discharge air, supply air) 

14 

Switching key 

Fan speed status (hi/medium/low) 

15 

Timing key 

Mode status (Auto, Bypass, 

Heat exchange) 

16 

On/Off key 

Error status 

17 

Reset key 

Filter cleaning status 

18 

Child lock icon 

Notice: For FHBQ-D15 and FHBQ-D20, there is no discharge air and supply air modes for the item number 5 and fan 

speed is uncontrolled for the item number 6.

Summary of Contents for EH01100030





































Reviews: