Gree CM100N1480 Service Manual Download Page 131 | Manualshive

Page: 131 / 266

background image

GREE

Multi Variable Air Conditioners Indoor Unit

125

3.15.3 Installation Notice

(1) Installation dimension (refer to the outline dimension in the figure).
(2) Installation foundation.
(3) Make sure the top hanging rod, ceiling and building structure have sufficient strength to

withstand the weight of unit.

(4) Installation site and environment.

1) Keep the unit from insolation and rain.

2) Keep the unit from fire, flammable objects, corrosive gap or exhaust gas.
3) Please reserve ventilation space.
4) Please reserve sufficient space for maintenance.
5) Please take proper measures to reduce noise and vibration.

(5) Electrical installation of unit.
All electrical installation must be done by professionals according to national and local laws and

regulations.

The unit must be grounded reliably. Please connect wire according to the wiring diagram on the unit.

3.15.4 Selection of Air Switch and Power Cord

Model

Power Cord Size

Air Switch

Capacity

(A)

Minimum Sectional

Area of Ground Wire

(mm

2

/AWG)

Minimum Sectional

Area of Power Cord

(mm

2

/AWG)

GMV-ND30PLS/C-T(U)

208/230V/60Hz

15

1.0/AWG18

1.0/AWG18

GMV-ND36PLS/C-T(U)

208/230V/60Hz

15

1.0/AWG18

1.0/AWG18

GMV-ND42PLS/C-T(U)

208/230V/60Hz

15

1.0/AWG18

1.0/AWG18

GMV-ND48PLS/C-T(U)

208/230V/60Hz

15

1.0/AWG18

1.0/AWG18

3.16 Installation of 360°Air Discharge Compact Cassette Type

Indoor Unit

3.16.1 Outline and Installation Dimension

«
...
129
130
131
132
133
...
»

Summary of Contents for CM100N1480











































































































































































































































































Reviews:

No comments

Related manuals for CM100N1480

Brand: b-mola Pages: 9

Brand: Zibro Pages: 122

Brand: Zibro Pages: 2

MWF-18CRN1-QC1G

Brand: Akai Pages: 40

AIR CONDITIONER SYSTEMS

Brand: DDB Pages: 12

Brand: Kaysun Pages: 12

Brand: Olmo Pages: 37

Brand: WAGNER Pages: 5

Brand: GE Pages: 32

Brand: TaoTronics Pages: 15

Brand: Easy@Home Pages: 56

Brand: Hunter Pages: 14

Brand: Adler Europe Pages: 80

Brand: Haier Pages: 75

Brand: innovair Pages: 82

Brand: Clean Air Pages: 4

Aerosphere World

Brand: Valeo Pages: 61

Brand: Technibel Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands