Do not fly unless your propeller, spinner and
spinner backplate are precision balanced, using a
"high-point" or similar balancer.
Do not use a propeller that will produce exces-
sively high speeds. 6" Pitch is recommended for 2-
cycle engines, and 8" pitch is recommended for 4-cy-
cles.
Before each flight, inspect the clevises, horns,
pushrods and all other parts of the control linkages,
checking for any play that may have developed due
to wear. Especially watch for enlargement of the
holes in the nylon horns and servo arms, loose screws
and nuts, and worn servo mounting grommets. Re-
place worn parts immediately.
GOOD LUCK AND GREAT FLYING!
PART#
QTY
DESCRIPTION
PARTS LIST
PART#
QTY
DESCRIPTION
CANPY037
PLTB002
SS90F01
SS90F05
SS90F06
SS90F27
SS90F32
SS90P01
SS90P02
SS90P03
WIRES17
WPNTS003
SS90A01
PLY3021
PLY3022
SS90F03
SS90F08
SS90F18
SS90F41
SS90F43
SS90F44
5590503
5590504
SS90W17
SS90W18
SS90W19
SS90W20
SS90W21
SS90W22
SS90W32
f f
Note: "DC"
Clear Plastic Canopy
Plastic 36" Outer Pushrod
Tubes
Balsa Shaped 3/16 Fuselage
Side
Balsa Shaped 13/16 Chin
Block
Hardwood Shaped 5/8 Engine
Mount Rail
Balsa 3/8x1-3/8x21-1/4
Hood Side Block
3-Ply 1/8 DC* Fuse Doubler
Fuselage Plan
Wing Plan
Instructions
Wire 2-56 x 34" Pushrod,
Threaded One End
ABS Plastic Wheel Pants Set
HARDWOOD PARTS
3-Ply 1/16 DC Spinner Ring
3-Ply 1/16 DC Landing Gear
Braces
5-Ply Shaped 3/8 F-l
Firewall
5-Ply 1/4x1-1/2x4-5/16
Wing Bolt Plate
5-Ply 3/16 x 1/2 x 4-3/32 Servo
Rails
3-Ply 1/32 x 1 x 1 Spinner
Ring Spacer
3-Ply 1/8 X 3/8 X 3-5/8 Servo
Rail Supports
5-Ply 1/4x1x1 Stab
Reinforcement Block
5-Ply Shaped 1/4 Front Stab
Brace
5-Ply 1/4x1/2x6
Rear Stab Brace
Hardwood 5/16 Diax 4-1/2
Wing Dowel
Hardwood 1/2 x 3/4 x 7-3/4
Landing Gear Block
Hardwood 1/2 x 3/4 x 29/32
Landing Gear Block Support
Hardwood 1/2 x 3/4 x 1/2
Landing Gear Block Gusset
5-Ply 1/8x1-3/4x1-3/4
Wheel Pants Screw Plate
3-Ply 1/16x1x1 Wing
Bolt Plate
5-Ply 1/8 x 3/8 x 5/8
Aileron Servo Rail
SS90A02
SS90F20
SS90F26
SS90F29
SS90F30
SS90F42
SS90A05
Die Cut
41
SS90F34
SS90F35
SS90F37
1 BALSA FUSELAGE
PARTS
Balsa Shaped 3/16 Rear
Fuse Side
Balsa 7/8 Fin Fairing
Balsa 1/2 Upper
Nose Side
Balsa Shaped 1/2 Lower
Nose Side
Balsa 1/2x5/8x4-13/16
Nose Side Fillers
SS90A03
SS90F09
SS90F10
SS90F11
SS90F12
SS90F16
•
SS90F17
SS90F19
SS90F21
SS90F25
SS90F28
SS90F40
SS90R02
SS90R03
SS90S02
SS90A04
SS90W33
SS90W34
SS90W35
1
1
1
1
1
1
1
2
1
1
2
1
1
1
1
1
8
3
1
BALSA FUSELAGE
PARTS
Balsa Shaped 1/4 F-3A
Bulkhead
Balsa Shaped 1/4 F-6A
Bulkhead
Balsa Shaped 5/8x3x3-1/2
Spinner Filler
Balsa 3/8x1/2x3-5/8
Nose Filler
Balsa 3/8x15/16x2-1/32
Stab Filler Block
Balsa 1/4x7/8x4-5/16
Fuse Cross-Brace
Balsa Shaped 3/16 Front
Fuse Side
Balsa Tapered 1/4 Tail Filler
Balsa 3/8x1x1 Fin Fairing
Balsa 3/16x5/8x4-7/8
Engine Rail Filler
Balsa 1/8x2-1/4x4
Fuel Tank Support
Balsa Shaped 1/4 Front
Fin Filler
Balsa 1/4 x 3 x 1-1/2 Rear
Fin Filler
Balsa 1/4x3-7/32x3
Stab Center
DIE CUT WING RIBS
Balsa 3/32 DC W-3 Wing Rib
Sheet
Balsa 3/32 DC W-2 Wing Rib
Sheet
Balsa 3/32 DC W-l Wing Rib
Sheet
DIE CUT FORMERS
3-Ply 1/8 DC Formers 5A,
4A,3B
3-Ply 1/8 DC Formers 1A,
1B,2A,2D
3-Ply 1/8 DC Formers F2,
F3.AB
