background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of

purchase. This warranty does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability
exceed the original cost of the purchased kit. 
Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.

To make a warranty claim send the defective part or item to Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822 USA

Include a letter stating your name, return shipping address, as much contact information as possible (daytime telephone number, fax
number, e-mail address), a detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package
the problem will be evaluated as quickly as possible.

READ THROUGH THIS MANUAL BEFORE STARTING
CONSTRUCTION.

IT CONTAINS IMPORTANT

INSTRUCTIONS AND WARNINGS CONCERNING THE
ASSEMBLY AND USE OF THIS MODEL.

GPMZ1121 for GPMA1121  V1.0

Entire Contents © Copyright 2006

Champaign, Illinois

(217) 398-8970, Ext 5

[email protected]

INSTRUCTION MANUAL

Wingspan: 36 in [915mm] 
Wing Area: 254 sq in [16.4dm

2

Weight: 8.5 – 9.5 oz [240 – 270g]
Wing Loading: 4.8 – 5.3 oz/sq ft [15 – 16g/dm

2

Length: 25 in [635mm] 
Radio: 4-channel minimum, 7A brushed ESC, 3 micro servos

and micro receiver

Summary of Contents for helicat

















Reviews: