background image

Pro 30-minute epoxy (GPMR6047)

Threadlocker thread locking cement (GPMR6060)

#1 Hobby knife (HCAR0105)

#11 blades (5-pack, HCAR0211)

#11 blades (100-pack, HCAR0311)

Drill bits: 1/16" [1.6 mm], 3/32" [2.4 mm], 1/8" [3.2 mm],
5/32" [4 mm], 3/16" [4.8 mm]

Small, flat metal file

Stick-on segmented lead weights (GPMQ4485)

Silver solder w/flux (GPMR8070)

21st Century

®

sealing iron (COVR2700) 

21st Century iron cover (COVR2702)

21st Century trim seal iron (COVR2750)

Here is a list of optional tools mentioned in the manual that
will help you build the Giant Super Sportster ARF.

2 oz. [57g] spray CA activator (GPMR6035)

Pro 6-minute epoxy (GPMR6045)

R/C-56 canopy glue (JOZR5007)

CA debonder (GPMR6039)

3M 75 repositionable spray adhesive (MMMR1900)

Epoxy brushes (6, GPMR8060)

Mixing sticks (50, GPMR8055)

Mixing cups (GPMR8056)

Medium T-pins (100, HCAR5150)

Robart Super Stand II (ROBP1402)

Masking tape (TOPR8018)

Wax paper

Denatured alcohol (for epoxy clean up)

Switch & Charge Jack Mounting Set (GPMM1000)

Panel Line Pen (TOPQ2510)

Rotary tool such as Dremel

Rotary tool reinforced cut-off wheel (GPMR8200)

Hobby Heat

micro torch (HCAR0750)

Dead Center

Engine Mount Hole Locator (GPMR8130)

AccuThrow

Deflection Gauge (GPMR2405)

CG Machine

(GPMR2400)

Laser incidence meter (GPMR4020)

Precision Magnetic Prop Balancer (TOPQ5700)

Aluminum Fuel Line Plug (GPMQ4166)

• The Giant Super Sportster ARF is factory-covered with Top

Flite

®

MonoKote

®

film. The following colors were used and

are available in six foot [1.8m] rolls. If only a small piece of
MonoKote is needed, maybe a modeling friend might have
some in his work shop. Some hobby shops also sell
MonoKote by the foot.

White (TOPQ0204)
Black (TOPQ0208)
True Red (TOPQ0227)

• The stabilizer and wing incidences and engine thrust

angles have been factory-built into this model. However,
some technically minded modelers may wish to check
these measurements anyway. To view this information visit
the web site at www.greatplanes.com and click on
“Technical Data.” Due to manufacturing tolerances which
will have little or no effect on the way your model will fly,
please expect slight deviations between your model and
the published values.

IMPORTANT BUILDING NOTES

Optional Supplies and Tools

5

ORDERING REPLACEMENT PARTS

Replacement parts for the Great Planes Giant Super Sportster
ARF are available using the order numbers in the Replacement
Parts List 
that follows. The fastest, most economical service can
be provided by your hobby dealer or mail-order company.

To locate a hobby dealer, visit the Hobbico

®

web site at

www.hobbico.com. Choose “Where to Buy” at the bottom of the menu
on the left side of the page. Follow the instructions provided on the page
to locate a U.S., Canadian or International dealer. If a hobby shop is not
available, replacement parts may also be ordered from Tower Hobbies

®

at www.towerhobbies.com, or by calling toll free (800) 637-6050.

Parts may also be ordered directly from Hobby Services by calling
(217) 398-0007, or via facsimile at (217) 398-7721, but full retail prices
and shipping and handling charges will apply. Illinois and Nevada
residents will also be charged sales tax. If ordering via fax, include a
Visa

®

or MasterCard

®

number and expiration date for payment. Mail

parts orders and payments by personal check to Hobby Services
at the address on the front cover of this manual.

Be certain to specify the order number exactly as listed in the
Replacement Parts List. Payment by credit card or personal check
only; no C.O.D.

If additional assistance is required for any reason contact Product
Support by e-mail at:

[email protected]

(217) 398-8970

Replacement Parts List

Order #

Description

How to Purchase

Missing pieces

Contact Product Support

Instruction manual

Contact Product Support

Full-size plans

Not available

Contact your hobby supplier to purchase these items:

GPMA2900 .......Wing
GPMA2901 .......Fuselage
GPMA2902 .......Tail Surface Set
GPMA2903 .......Landing Gear
GPMA2904 .......Cowl
GPMA2905 .......Wing Joiner Tube
GPMA2906 .......Canopy
GPMA2907 .......Spinner
GPMA2908 .......Decal Sheet

Summary of Contents for Giant Super Sportster

































Reviews: