manualshive.com logo in svg

GREAT PLAINS PL5500 PTO, Installation And Maintenance Manual

Share
Download
GREAT PLAINS PL5500 PTO Installation And Maintenance Manual Download Page 21

PL5500 PTO Pump Kit

Table of Contents

Great Plains

 | 411-774M | 2019

-

09

-

12

Table of Contents

19

2. Secure the oil cooler (29) to the fan mount (20) using

four bolts (21), four washers (27), and four nuts (23).

3. Using a measuring tape and grease pencil, measure

5 in (13 cm) from edge of the oil reservoir and mark

the measurement. 

4. Secure the fan mount (20) to the tongue about 5 in

(13 cm) behind the Oil Reservoir using  two u-bolts

(28), four locking washers (26), and four nuts (12).

Install Hydraulic Hoses

The new hoses may be installed in any order. Secure the

hoses  with  any  available  clamps  along  their  routes.

Remember  there  are  three  hydraulic  hoses  already

connected to the fan assembly. These hoses will remain

in  placed  and  are  necessary  to  install  PTO  pump

assembly  kit.  It  is  recommended  to  mark  all  hydraulic

hoses for convenience.

TP-71557

TP-71558

68689

841-196C

861-544C

861-544C

Summary of Contents for PL5500 PTO





























Reviews:

No comments

Brands by name

Popular brands

Load more brands