manualshive.com logo in svg

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Share
Download
GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 96

2019-03-11

Table of Contents

Index

407-502M

NP30A or NP40A

Table of Contents

Index

Adjustments

92

Wing Leveling

Before checking wing level, check that the center section

is level left to right (“

Rear Eyebolt Adjustment

”). On

2-point and pull-type, rear eyebolts above the rear

casters can affect left-right level if out of adjustment.

Wing Level: 2- and 3-Point

On 2-point and 3-point applicators, wing level is

controlled entirely by gauge wheel height. If wings are

not running level, adjust gauge wheels.

Wing Level: Pull-Type

On Pull-Type applicators, wing level is controlled by the

lift cylinders and the top eyebolt.
If wings get out of level, perform re-phasing operations

(page 51) until the lengths of the exposed rods are

identical across the applicator.
If the wings are still not level, check that the eyebolt

reveal is still at the factory setting (or is at least identical

at all eyebolts).

Refer to Figure 68

The factory setting is a distance of:

 3.5 in. (8.9 cm)

from the end of the eyebolt to the top face of the wheel

lug tube.
To adjust the eyebolt, loosen the hose guide nut  and

jam nut . Rotate the adjust nut  to set bolt reveal.

Tighten jam nut.

Rear Eyebolt Adjustment

On 2-point and Pull-Type applicators, side to side level at

rear is controlled by eyebolts at the lift cylinder bases. On

2-point, rear height is set by spacers (page 38).

On Pull-Type, rear height is controlled by the cylinders,

slaved to the hydraulic depth stop valve on the left wing.
Check that both eyebolts are set to the same reveal .
On Pull-Type, check front to back level (after re-phasing)

at full lift on level ground. If front eyebolts have been

changed from their factory settings, adjust the rear

eyebolts to bring the frame back into front-back level.

Refer to Figure 69

The factory setting is a distance of:

 3.5 in. (8.9 cm)

from the end of the eyebolt to the top face of the lug tube.
To adjust the eyebolt, loosen the hose guide nut , then

the jam nut . Rotate the adjust nut  to set bolt reveal.
Check that the hose loop  is on top.

Tighten jam nut , then hose guide nut .

Figure 68

Front Caster Wheel Eyebolt

31724

1

3

4

2

1

2

3

4

Figure 69

Rear Lift Eyebolt

31622

5

3

4

2

5

5

2

3

4

6

3

2

Summary of Contents for Nutri-Pro NP30A













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands