GREAT PLAINS Nutri-Pro NP30A Operator'S Manual Download Page 35

Page: 35 / 172

NP30A or NP40A

Table of Contents

Index

Preparation and Setup

2019-03-11

Table of Contents

Index

407-502M

2- and 3-Point Hitching

The NP30A or NP40A is engineered to be used with

Category II or Category III tractors.

Refer to Figure 7

This applicator is factory set for Category III tractors.

Category II requires an optional hitch pin kit (see

page 132).
In addition, the following bushings (not supplied by Great

Plains) may be needed to fit your quick hitch or tractor’s

3-point arms:

• Upper Link (full 3-point only):

1 inch (25.4 mm) I.D. x 1

inch (31.8 mm) O.D.

• Lower Links:

inch (28.6 mm) I.D. x 1

in (36.5 mm) O.D.

1. Adjust tractor lower links to maximize lifting height.
2. Normally the lower arms engage pins in the lower

holes of the applicator’s three point lugs. You may

use the upper holes if necessary.

3. Set tractor sway blocks to minimize side sway. Set

tractor hitch lift control to Float.

4. Back tractor up to applicator. Align lower links with

the lower hitch clevis on applicator. Adjust hitch

bushings and spacers supplied with applicator

according to the category of your tractor. Lock pins in

place.

5. Set hitch for depth control mode.

Full 3-Point Hitching

For 2-Point hitching (3-Point semi-mounted), continue at

“

Electrical Hookup

” (next topic).

Determine which top holes to use:

Attach tractor top link to applicator upper hitch clevis.
For intended results, the frame must be level side-to-side

and front-to-back. This must be done in the field, and

cannot normally be established at first hitching. See

“

Leveling Applicator

” on page 38.

Upper

Category III

Middle

Category III Quick Hitch

Category III
Category II

a. Requires an optional hitch pin kit (page 132)

Lower

Category II

Quick Hitch

Figure 7

3-Point Hitch Pins

21673

Category III

Category II

Crushing Hazard:

Do not stand or place any body part between
applicator and moving tractor. You may be

severely injured or killed by being crushed

between the tractor and applicator. Stop tractor engine and set
parking brake before attaching cables and hoses.

Figure 8

3-Point Top Pins

31078

Summary of Contents for Nutri-Pro NP30A













































































































































































Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands

GREAT PLAINS Nutri-Pro NP30A, Operator'S Manual

Search results

Summary of Contents for Nutri-Pro NP30A

Reviews:

Related manuals for Nutri-Pro NP30A

Brands by name

Popular brands