GREAT PLAINS 3S-3000HD Operator'S Manual Download Page 98

Page: 98 / 116

3S-3000HD

Table of Contents Index

Great Plains Manufacturing, Inc.

195-068M

Table of Contents Index

2019-03-12

Removable Partition

This partition reduces side-to-side seed flow in the small

seeds box. This can prevent seed pile-up when drilling

across slopes and in other situations where the seed is

particularly fluid. Order one per partition.

FigureSpacer

Seed Tube Plug (Small Seeds)

This plug stops seed flow from the small seeds box

above the meter. Order one per row to set inactive.

FigureSpacer

Opener Disk Scraper

Optional disk scrapers help clear any soil and debris not

removed by the standard disk spreaders at the seed

tube. Scrapers cannot be mounted if optional seed

firmers are used. Scrapers are compatible with the

standard seed flap.

See “

Scraper Installation

” on page 105, and

“

Disk Scraper Adjustments

” on page 56.

FigureSpacer

Description

Part

Number

RMVBL SMALL SEED BOX PARTITION

123-409D

FigureSpacer

17028

Description

Part Number

SML SDS CUP PLUG

133-315H

FigureSpacer

27407

Description

Part Number

00HD Scraper Assembly

(Order one per row)

122-015A

FigureSpacer

26460

Summary of Contents for 3S-3000HD





















































































































Search results

Summary of Contents for 3S-3000HD

Reviews:

Brands by name

Popular brands

GREAT PLAINS 3S-3000HD, Operator'S Manual

Search results

Summary of Contents for 3S-3000HD

Reviews:

Brands by name

Popular brands