manualshive.com logo in svg

GREAT PLAINS 3S-3000HD, Operator'S Manual

Share
Download
GREAT PLAINS 3S-3000HD Operator'S Manual Download Page 109

2019-03-12

Table of Contents Index

195-068M

Great Plains Manufacturing, Inc.

Table of Contents Index

105

Appendix B - Initial Setup

Scraper Installation

Optional disk scrapers are not factory installed. To install 

them in the field:
1. Remove one or both disk blades to gain safe access 

to the mount. Note the position of bushings and 

spacers for correct re-assembly (page 56).

Refer to Figure 94

2. Position the inside scraper mount   to the rear of 

the seed firmer mount   on the opener weldment.

Secure it with two HHCS 

3

8

-16x1in hex head bolts, 

lock washers and nuts. Insert the bolts from the front.

3. Position the scraper blade   below and behind the 

inside scraper mount  , with the notch on top to 

machine right.

Secure it loosely with one RHSNB 

3

8

-16x1 round 

head square neck bolt, flat washer, lock washer and 

nut.

4. Re-mount the removed disk blade.
5. Adjust the scraper blade per “

Disk Scraper Adjust-

ments

” on page 56.

FigureSpacer

Figure 94

Scraper Installation

26460

2

1

3

1

2

3

1

Summary of Contents for 3S-3000HD





















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands