GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 83

Page: 83 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

2018-06-18

Table of Contents

Index

195-441M

Opener-Frame Clearance

Refer to Figure 89

When fully raised, top of opener mounts

should clear

bottom of drill frame tube by at least



inch (12.7mm).

To adjust opener frames so all openers have the same
clearance, loosen jam nut

on opener lift cylinders and

turn adjustment nut. When openers are at the correct
height, tighten jam nut. Repeat at each opener lift
cylinder if necessary.

Marker Maintenance

Marker Transport Carrier

When marker is folded, the second section should be
centered in transport carrier saddle and be parallel with
top of drill box.

Refer to Figure 90

To adjust height of saddle, loosen



x2in U-bolts

that

hold carrier tube to mounting bracket. Slide carrier tube
up or down as needed.

Marker Shear Bolt

The marker arm is attached to marker body with a shear
bolt

, which is intended to fail if the marker strikes an

obstruction, allowing the marker to swing back around a
second bolt

If the shear bolt breaks, replace it with an equivalent



-16x2in Grade 2 bolt (Great Plains part 802-266C). If

that size is not available in your local market, temporarily
substitute an M10x1.5 Class 5.8 metric bolt and nut.



NOTE:

Replacing the bolt with a lower grade, or smaller size,
can result in nuisance shears.

Equipment Damage Risk:

Replacing the bolt with a higher grade can result in marker
damage.

Figure 89

Opener Frame Clearance

18853

Figure 90

Marker Transport Carrier

15632

Figure 91

Marker Shear Bolt

15669

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands