GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 77

Page: 77 / 118

3S-3000/F/HD/HDF

Table of Contents

Index

Maintenance and Lubrication

2018-06-18

Table of Contents

Index

195-441M

In-Line Filters

If the raising or lowering times of the openers slow
noticeably, check the in-line filters and clean if needed.

Refer to Figure 77

Two filters are located on one each of the down-pressure
adjustment valves. If the Point Row option is installed,
another filter is located on the third adjustment valve

Refer to Figure 78

To disassemble unscrew end cap of filter. Remove top
retaining washer and screen.

Clean filter screen with solvent and compressed air, or
replace if needed.

When reassembling put screen into filter. Place retaining
washer on top of filter and screw on end cap.

Figure 77

In-Line Filter Locations

22968

Figure 78

In-Line Filter

25187

Summary of Contents for 3S-3000-3210























































































































Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands

GREAT PLAINS 3S-3000-3210, Operator'S Manual

Search results

Summary of Contents for 3S-3000-3210

Reviews:

Related manuals for 3S-3000-3210

Brands by name

Popular brands