GREAT PLAINS 3S-3000-3210 Operator'S Manual Download Page 22 | Manualshive

Page: 22 / 118

background image

2018-06-18

Table of Contents

195-441M

3S-3000/F/HD/HDF

Table of Contents

Preparation and Setup

18

Refer to Figure 4 and Figure 5

1.

Adjust the drill hitch to match your tractor-drawbar
height. Mount tongue jack on side of tongue. Use
jack to raise drill tongue so lowest hitch hole is
18 inches (45.7cm) above ground level with drill
lowered to FIELD position.

Refer to Figure 5

2.

Bolt drill hitch onto drill tongue to match your
tractor-drawbar height. You can turn the hitch over
for a total of six different hitch heights. Always have
two (2) bolts in two holes of both tongue and hitch.



NOTE:

When hitching drill to a different tractor, check for a
difference in drawbar heights. If heights are different,
readjust hitch height accordingly.

3.

Securely attach safety chain to an anchor on a
tractor capable of pulling the drill.

Refer to Figure 6

4.

Use crank to raise jack foot. Remove pin and jack.
Store jack on top of tongue.

Figure 4

Jack in Lifting Location

15564

Figure 5

Heights for Various Hitch Positions - Correct Tongue Height

15623

32.0in

81.3cm

29.0in

73.7cm

26.0in

66.0cm

21.5in

54.6cm

18.5in

47.0cm

15.5in

39.4cm

18.0in

45.7cm

Figure 6

Jack in Storage Location

15563

«
...
20
21
22
23
24
...
»

Summary of Contents for 3S-3000-3210























































































































Reviews:

No comments

Related manuals for 3S-3000-3210

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands