Gravely Promaster 260Z Service Manual Download Page 8

 8

Figure 2 - Safety Decals

SAFETY RULES

Read, understand, and follow all safety practices in 
Owner/Operator Manual before beginning assembly. 
Failure to follow instructions could result in personal 
injury and/or damage to unit.

ALWAYS remove key from ignition and wire from spark 
plug before assembly. Unintentional engine start up 
can cause death or serious injury.

Complete a walk around inspection of unit and work 
area to understand:

• Work area

• Your unit

• All safety decals

Inspect unit before each use for: missing or damaged 
decals and shields, correctly operating safety interlock 
system, and deterioration of grass catchers. Replace or 
repair as needed.

ALWAYS check overhead and side clearances carefully 
before operation. ALWAYS be aware of traffic when 
crossing or operating along streets or curbs.

Keep children and people away.

Keep children out of work area and under watchful care 
of a responsible adult.

Keep area of operation clear of all toys, and debris. 
Thrown objects can cause injury.

Check for weak spots on docks, ramps or floors, Avoid 
uneven work areas and rough terrain. Stay alert for 
hidden hazards or traffic.

DO NOT operate near drop-offs, ditches, or 
embankments. Unit can suddenly turn over if a wheel is 
over the edge of a cliff or ditch, or if an edge caves in.

Data indicates that operators, age 60 and above, are 
involved in a larger percentage of riding mower related 
injuries. These operators should evaluate their ability to 
operate the riding mower safely enough to protect 
themselves and others from serious injury.

Read the entire Owner/Operator manual and other 
training material. If the operator or the mechanic 
cannot read the manual, it is the owner’s responsibility 
to explain it to them. Only the user can prevent and is 
responsible for accidents or injuries occurring to 
themselves, other people or property.

Only trained adults may operate unit. Training includes 
actual operation.

OF 1624

   

  

      

    

 

      

 

      

• Risque de blessures - ne pas s’approcher des pièces en

mouvement.

• Evitar lesiones - Mantenerse alejado de las piezas giratorias.

• Avoid injury - Stay clear of rotating parts.

07735200C

DANGER / PELIGRO

DANGER / PELIGRO

WARNING/AVERTISSEMENT/ADVERTENCIA

Do not operate mower
unless guards are in
operating position or
bagger is attached.

Ne jamais utiliser
la tondeuse sans
protecteur sur le
canal d'ejection ou
sans le bac monte.

No operar segadora a
menos que las defensas
esten en posicion de
operacion o el
recogedor este fijo.

07742300B

DANGER / PELIGRO

• Read the operator's manual.
• Keep children and others away from unit while

operating.

• Never direct discharge toward other people.

Thrown objects can cause injury.

• Look down and behind before and while backing.
• Never carry children.
• Go up and down slopes, not across.

• If machine stops going uphill, stop blade and

back down slowly.

• Avoid sudden turns.
• Keep safety devices (guards, shields, switches,

etc.) in place and working.

• Check interlock system per manual before use.
• Understand location and function of all controls.
• Never allow operation by untrained persons.

• Leer el manual del operador.
• Mantenga la unidad alejada de los niños y otras

personas cuando esté en funcionamiento.

• Nunca dirija la descarga hacia otras personas,

ya que los objetos lanzados pueden provocar
lesiones.

• Antes y durante retroceso mirar hacia abajo y

detras.

• Nunca monten niños.
• Suba y baje pendientes, no transversalmente.
• Si la maquina se detiene subiendo cuesta,

desactive la cuchilla y baje lentamente.

• Evite viradas subitas.
• Mantenga artefactos de seguridad (defensas,

protectores, interruptores, etc.) en su lugar y
trabajando.

• Verifique en el manual el sistema de engranar

antes de usar.

• Tenga conocimiento de funciones y

localizaciones de todos los controles.

• No permitir que personal sin la necesaria

formación use la máquina.

TO AVOID SERIOUS INJURY OR DEATH

POUR EVITER LES BLESSURES GRAVES
OU LA MORT

PARA EVITAR DAÑOS SERIOS O LA
MUERTE

• Lire le manuel d'utilisation.
• Éloigner les enfants et tout autre personne

pendant le fonctionnement de la machine.

• Ne jamais décharger directement en direction

de quelqu’un. Des particules projetées
peuvent provoquer des blessures.

• Regardez derrière et sur les côtés lorsque

vous reculez.

• Ne transportez jamais d'enfant.
• Tondez toujours de haut en bas et

inversement jamais le long des pentes.

• Si la machine s'arrête en montee. Debrayez

la lame et redescendez doucement.

• Evitez les virages brusques.
• Maintenez toujours en place tous les

elements de sécurité (protecteurs,

  interrupteurs, etc.).
• Controler le bon fonctionnement du système

de sécurité avant utilisation tel qu'indiqué
dans le manuel d'utilisation.

• Comprenez bien la fonction et la situation de

chacun des leviers et boutons de commande.

• Ne jamais permettre l'utilisation par des

personnes n'ayant pas reçu la formation
nécessaire.

MAX

17

05359300

DA N G E R   /  P E L I G RO

Summary of Contents for Promaster 260Z
















































Reviews: