Gravely 988100 Owner'S/Operator'S Manual Download Page 16

GB-16

*

 Change oil after first 8 hours of operation and every 100 

hours thereafter.

MAINTENANCE SCHEDULE

Period

Service

Task

Each Use

Check Safety Interlock System

WARNING: 

Safety interlock system failure and improper operation of unit 

can result in death or serious injury. Test this system each time the unit is 
operated. If this system does not function as described, do not operate until 
repairs are made. See Check Safety Interlock System on page 10.

Check Air Cleaner

Check the air cleaner element before each use. See engine manual for 
detailed instructions.

Check Engine Oil

Check the engine oil level before each use. Never operate the engine when 
the oil level is low. See engine manual for detailed instructions.

Check Engine Cooling

Check the engine air cooling system before each use. See engine manual for 
detailed instructions.

Check Fasteners

Check all nuts, bolts, and other fasteners before each use. Replace missing 
or damaged fasteners.

Check Tire Pressure

Check tires for proper inflation, excessive wear or damage before each use. 
The correct air pressure is 8 to 16 psi (55 to 110 kPa).

Follow Engine Manual 
Maintenance Schedule

Perform scheduled engine maintenance. See engine manual for detailed 
instructions.

Every 25 
Hours

Check All Belts

Check all belts for wear or damage. If belts slip, check for damaged belt 
tensioner.

Mower Blades

Check mower blades for wear. Sharpen or replace as needed. See Mower 
Blades 
on page 21.

Clean Air Cleaner Foam 
Element

See engine manual for detailed instructions.

Every 50 
Hours

General Lubrication

Oil all pivot points and pin connections. Grease lube fittings. See General 
Lubrication 
on page 17.

Every 100 
Hours

Change Engine Oil

*

Open the petcock to drain oil through oil drain hole on the left side of engine. 
See engine manual for additional instructions.

Check Fuel Filter

See engine manual for detailed instructions.

Check Spark Plug

See engine manual for detailed instructions.

Check Muffler

Check muffler for damage or wear. Replace if necessary.

Clean Air Cleaner Paper 
Element

See engine manual for detailed instructions.

Summary of Contents for 988100





























Reviews: