Gravely 927060 - 1028 Owner'S/Operator'S Manual Download Page 13

 

GB - 13

 

25 Hours 

or Every 

Season

 

Check Battery

Keep battery and battery terminals clean (see 

 

Cleaning 

Battery and Battery Cables

 

 on page 20).

Lubricate Unit

Apply grease to two front 
wheel zerks, steering 
gear, and pinion.

Clean Air Filter

 

1

 

Clean air filter (item 2). Refer to Engine Manual for detailed 
instructions.

 

50 Hours 

or Every 

Season

 

Change Engine Oil

 

2

Drain engine oil by opening oil drain petcock (item 6). Refer 
to Engine Manual for detailed instructions.

Check Fasteners

Check mower blade mounting hardware and all other 
fasteners. Replace fasteners that are missing or damaged. 
Tighten all nuts and bolts to the correct torque value.

Inspect Muffler and 
Spark Arrestor

Replace muffler (item 5) and spark arrestor (if equipped) if 
corroded. Contact your Gravely Dealer.

100 Hours 

or Every 

Season

Replace Spark Plug

Replace spark plug (item 4). Refer to Engine Manual for 
detailed instructions.

Replace Fuel Filter

Replace fuel filter (item 3). Refer to Engine Manual for 
detailed instructions.

Clean Cooling 
System

1

Clean cooling system (item 1). Refer to Engine Manual for 
detailed instructions.

Check All Belts

Replace worn or deteriorated belts.

• Check hydrostatic belt (see 

Hydrostatic Belt 

Replacement

 on page 21).

• Check PTO belt (see 

PTO Belt Replacement

 on 

page 21).

• Check mower belt (see 

Mower Belt Replacement 

(927064)

 on page 22). 

Service more often when operating under heavy loads, high temperatures, or dusty 

conditions. Replace air filter if very dirty.

2

 Change after first 5 to 8 hours of use. Change every 25 hours when operating under heavy 

loads or in high temperatures.

Interval

Task

Action

Zerk

Steering 
Gear and 
Pinion

Zerk

Summary of Contents for 927060 - 1028




























Reviews: