background image

 

22 

 

Whenever you are working on the engine, make sure that you are on a safe 
surface and cannot slip. Get used to holding the model really securely. 
 

 

Take-off and landing strips should be kept free of unauthorised people and 
movable obstacles, particularly when a model is using the strip. 
 

 

Watch  the  aeroplane  constantly  while  it  is  in  the  air.  Models  must  always 
give way to full-size aircraft. 
 

 

Don’t operate your aircraft from public roads, squares, school playgrounds, 
public parks or sports grounds etc., and ensure that you are always in full 
control of the model. 
 

 

It  is  important  that  you  are  able  to  stop  your  engine  at  any  time.  This  is 
achieved  by  adjusting  the  throttle  so  that  the  barrel  closes  completely 
when  you  move  the  throttle  stick  and  trim  to  their  end-points.  If  this  does 
not  work,  pinch  the  fuel  feed  line  between  your  fingers  or  pull  it  off  the 
carburettor. Never try to stop the engine by grasping the flywheel, propeller 
or spinner! 
 

 

All model flyers should behave in a manner which minimises the danger to 
people  and  property.  Never  act  in  any  way  which  will  disturb  other  flyers 
and jeopardise safe, orderly flying at the site. 
 

In  legal  terms  our  models  are  classed  as  aircraft,  and  as  such  are  subject  to 
legal regulations and restrictions which must be observed. 

 

Our  brochure  “Modellflugrecht,  Paragrafen  und  mehr”  (Model  Aviation  Law, 
Legal  Requirements  and  more)  is  available  under  Order  No.  8034.02,  and 
contains  a  summary  of  all  these  rules.  Your  local  model  shop  should  have  a 
copy  which  you  can  read.  Models  fitted  with  glowplug  engines  may  only  be 
flown with the landowner’s permission, and third party insurance is mandatory. 
There  are  also  Post  Office  regulations  concerning  your  radio  control  system, 
and these must be observed at all times. 

 

Please don’t misunderstand the purpose of these notes. We only want to make 
you  aware  of  the  many  dangers  and  hazards  which  can  arise  if  you  lack 
knowledge  and  experience,  or  work  carelessly  or  irresponsibly.  If  you  take 
reasonable  care,  model  flying  is  a  highly  creative,  instructive,  enjoyable  and 
relaxing pastime. 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for TAXI SPORT II

























Reviews: