manualshive.com logo in svg

GRASS VALLEY KAM-SD-2AES-DMX, Instruction Manual

Share
Download
GRASS VALLEY KAM-SD-2AES-DMX Instruction Manual Download Page 27

KAM-SD-2AES-DMX Instruction Manual

27

KAM-SD-2AES-DMX Links and Web Pages

 

Input/Output Configuration Web Page

Use the I/O Config web page to:

•

View a graphical overview of the currently installed rear module con-
nectors, 

•

See signal status of inputs,

•

Set the AES audio output connector type with the 

Balanced

 or 

Unbalanced

 

radio buttons, and

•

Assign easily recognized signal names that will help later in the config-
uration process.

Figure 12

 illustrates the I/O Config web page for the KAM-AES-R passive 

rear module required for the KAM-SD-2AES-DMX front module set for 
unbalanced AES audio outputs (

Unbalanced 

radio button selected).

Note

Only the selected AES outputs are valid. Unconfigured AES outputs are 
invalid and should not be used.

Figure 12.  KAM-AES-R Rear Module I/O Config Web Page (Unbalanced AES Outputs)

Use
this
link

Select AES output type

Summary of Contents for KAM-SD-2AES-DMX







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands