GRASS VALLEY IQUCP25 User Manual Download

Page: 262 / 338

262

Getting Started with the Multiviewer

Quick Edit of Project

3 Click on the tile background.
4 In the

Properties

box, select the ‘Extended Style > Background Color’ property.

5 Click on the ... icon to show the

Background Color

dialog. See

Figure 8-13

on page

262.

6 Select a color and click

Fig. 8-13: Color Picked

7 Click the

Save File

icon in the main tool bar to save the tile change.

Fig. 8-14: Tile with New Background Color

8 Click on the x on the tile tab to close the tile.

Alpha 255 entered

(fully opaque)

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands