GRASS VALLEY IQUCP25 User Manual Download

Page: 217 / 338

217

UCP

3901

User Manual

Logging - Input Info

The

Logging - Input Info

page shows SDI log message types: Log field names and current

log values are listed. Information on various parameters can be made available to a logging

device connected to the RollCall network. The information below describes the various

parameters available for logging. For the UCP-3901, logging must be configured and

enabled; see

Logging - Configuration (UCP

3901 Only)

on page 216.

Figure 7 - 19:

Logging SDI Info Page

The logging page comprises three columns:

Logging Page

Column

Description

Input Change

Time pane

Logs the time at which the input changed.

Input Change

Counts pane

Logs number of times that the input has changed standard or has

been removed.

Log Enable

Log Field

Log Value

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands