GRASS VALLEY IQUCP25 User Manual Download

Page: 164 / 338

164

Essence Processing SDC

Setup

Main Mod Level

Main PCB modification level.

Main HW Build

Factory main hardware build number.

Feature PCB

(IQUCP25 /

IQUCP50)

Daughter board PCB revision number.

Feature Mod Level

(IQUCP25 /

IQUCP50)

Daughter board PCB modification level.

Feature HW Build

(IQUCP25 /

IQUCP50)

Factory daughter board hardware build number.

Restart

Power-cycles the card. This will produce disturbances on the output

picture.

Note:

Restarting the card will affect all outputs.

Defaults

Provides options to reset the card to its defaults.

Default Settings:

All settings are reset to their default values,

except

for network configuration and IP addresses.

Factory Defaults:

All settings are reset to their default values,

including

network configuration and IP addresses.

Remove Licenses Click to remove any license currently enabled on the card. A restart is

required for this to take effect.

Parameter

Description

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands