GRASS VALLEY IQUCP25 User Manual Download

Page: 112 / 338

112

Essence Processing SDC

Configuring the Streams for use with 4K UHD SQDS

4 Configure each of the four UCP

3901 / IQUCP25 / IQUCP50 spigots that are to receive /

send the four HD sub-images. These links are assigned in groups of 4 as shown by the

Spigots

parameter. For example Spigots 1 to 4, Spigots 5 to 8, Spigots 9 to 12, and

Spigots 13 to 16.

5 Connect the quad link signals to the rear panel.

• For the UCP

3901:

12G/3G/HD/SD-SDI I/O – Serial digital video inputs / outputs (4)

on page 34 and

3G / HD / SD SDI I/O – Serial digital video inputs / outputs (12)

page 35.

• For the IQUCP25 / IQUCP50:

Images of Rear Panel Connectors

on page 46.

Configuring the Streams for use with 4K UHD SQDS

To support 4K streams, a quad-link (square division) configuration can be used. That is, the

4K image is divided into four HD quadrants, and each quadrant is sent as four separate

streams. These four streams must be logically linked together so that they are switched

together at once ensuring that there is no switching delay between the four streams that

would create visible glitches between the four quadrants.
The following shows the typical video stream composition of a 4K quad-link display.

PREREQUISITES:

• Configure each of the four UCP

3901 / IQUCP25 / IQUCP50 spigots that are to receive /

send the four quad-link images. These links are assigned in groups of 4 as shown by the

Spigots

parameter. For example Spigots 1 to 4, Spigots 5 to 8, Spigots 9 to 12, and

Spigots 13 to 16.

To configure a 4K UHD Quad Link Square Division input or output

1 Open the

Link Control

page. See

Link Control

on page 110.

2 Set

Enable

for the four spigots on which a quad link signal will be used (Spigots 1 to 4,

Spigots 5 to 8, Spigots 9 to 12, and Spigots 13 to 16).

3 Set the

SDQS

check box to use Square Division signals.

4 Configure each of the four UCP

3901 / IQUCP25 / IQUCP50 spigots that are to receive /

send the four quad-link images. These links are assigned in groups of 4 as shown by the

Spigots

parameter. For example Spigots 1 to 4, Spigots 5 to 8, Spigots 9 to 12, and

Spigots 13 to 16.

5 Connect the quad link signals to the rear panel.

Quadrant 1, Link 1

Quadrant 2, Link 2

Quadrant 3, Link 3

Quadrant 4, Link 4

4K UHD Composite Image

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands