GRASS VALLEY IQUCP25 User Manual Download

Page: 110 / 338

110

Essence Processing SDC

Link Control

Link Control

The

Link Control

page sets the configuration for 4K UHD support. These controls affect

both the Spigot and TPG configuration.

Figure 6 - 17:

Link Control Page

Parameter

Description

Spigots

When

Enable

is set, this show the 4 spigots that are to be used for the

4K UHD quad link signals. The individual spigots must be configured

as HD signals. See

Input Spigots

on page 122 and

Output Spigots

page 127.
To know on which HD-BNC input / output each spigot is available on

the rear panel, see:

• For the UCP

3901:

12G/3G/HD/SD-SDI I/O – Serial digital video

inputs / outputs (4)

on page 34 and

3G / HD / SD SDI I/O – Serial

digital video inputs / outputs (12)

on page 35.

• For the IQUCP25 / IQUCP50:

Images of Rear Panel Connectors

page 46.

Enable

Enable the quartet of spigots to be used for UHD Quad Links as

required.

• Set

Enable

• For non-12G configurations where link control is to treat each

associated spigots as a Quad Linked (QL) SDI, representing a

4K UHD signal. See

Use Case 2

on page 78.

• For 12G configurations, whether 12G-SDI or 4 x 3G-SDI, there

is only one resultant 12G ST2110-20 flow. See

Use Case 4

page 78 and

Use Case 5

on page 79.

• Deselect

Enable

allows the card to process SD/HD/3G-SDI.

Summary of Contents for IQUCP25



















































































































































































































































































































































Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands

GRASS VALLEY IQUCP25, User Manual

Search results

Summary of Contents for IQUCP25

Reviews:

Related manuals for IQUCP25

Brands by name

Popular brands