GRASS VALLEY 8920ADC - Instruction Manual Download Page 29 | Manualshive

Page: 29 / 40

background image

8920ADC Instruction Manual

29

Configuration

Software Update Web Page

The Software Update page (

) is not used to update 8920ADC soft-

ware. For instructions on updating to the latest software, refer first to the
8920ADC Release Notes that accompany the software update for complete
details.

Currently, the only recommended method of software updating is done
with a software kit (8900-FLOAD-CBL) that includes a CD-ROM with the
current software files and a serial cable assembly available from Grass
Valley.

Refer to the 8900-FLOAD-CBL Software Upgrade Instruction Manual in
PDF format on the CD-ROM for complete updating instructions and the
required software files for the module.

Figure 13. 8920ADC Software Update Web Page

Use
this
link

«
...
27
28
29
30
31
...
»

Summary of Contents for 8920ADC -









































Reviews:

No comments

Related manuals for 8920ADC -

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 174

Brand: kaiboer Pages: 16

iSignager iS-1620

Brand: QNAP Pages: 9

E-TBT-FRL-FD-01

Brand: Transition Networks Pages: 1

UNITISERVE-SSD -

Brand: NAIM Pages: 27

Brand: FONESTAR Pages: 9

Brand: DeLOCK Pages: 16

Brand: Dometic Pages: 292

Brand: Littfinski Daten Technik Pages: 2

Brand: MODIX Pages: 26

Brand: CYP Pages: 9

Brand: CYP Pages: 16

Brand: MOOD Pages: 5

Brand: Transition Networks Pages: 7

Brand: Datavideo Pages: 23

Brand: SoundMax Pages: 28

Brand: Hall Research Technologies Pages: 5

Brand: Hopewind Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands