GRASS VALLEY 7500NB Instruction Manual Download Page 19

Page: 19 / 92

7500 Series Instruction Manual

1-3

System Level Architecture

Two of the two bay, 12RU matrices are connected using expansion connec-
tors to create a fully configured 512x512 system. The system uses eight
input modules, eight output modules, and thirty-two crosspoint modules
as shown in

Figure 1-3

. The top bay is always used for inputs 1-128, the

second one for inputs 129-256, the third for 255-384, and the fourth bay is
used for inputs 385-512.

Figure 1-3. 7500NB Module Placement

7500NB 256x256

Power

Supply

Power

Supply

Inputs 1-64

Xpt Expansion Slot

Xpt (In=1-128, Out=1-64)

Outputs 1-64

Xpt (In=1-128, Out=129-192)

Xpt (In=1-128, Out=193-256)

Outputs 65-128

Xpt (In=1-128, Out=65-128)

Xpt Expansion Slot

Inputs 65-128

Matrix Controller 1

Inputs 129-192

Xpt Expansion Slot

Xpt (In=129-256, Out=1-64)

Outputs 129-192

Xpt (In=129-256, Out=129-192)

Xpt (In=129-256, Out=193-256)

Outputs 193-256

Xpt (In=129-256, Out=65-128)

Xpt Expansion Slot

Inputs 193-256

Matrix Controller 2

Power

Supply

Power

Supply

Inputs 257-320

Xpt (In=257-384, Out=1-64)

Xpt (In=257-384, Out=129-192)

Xpt (In=257-384, Out=257-320)

Outputs 257-320

Xpt (In=257-384, Out=385-448)

Xpt (In=257-384, Out=449-512)

Outputs 321-384

Xpt (In=257-384, Out=321-384)

Xpt (In=257-384, Out=193-256)

Xpt (In=257-384, Out=65-128)

Inputs 321-384

Matrix Controller 3

Inputs 385-448

Xpt (In=385-512, Out=1-64)

Xpt (In=385-512, Out=129-192)

Xpt (In=385-512, Out=257-320)

Outputs 385-448

Xpt (In=385-512, Out=385-448)

Xpt (In=385-512, Out=449-512)

Outputs 449-512

Xpt (In=385-512, Out=321-384)

Xpt (In=385-512, Out=193-256)

Xpt (In=385-512, Out=65-128)

Inputs 449-512

Matrix Controller 4

7500NB 512x512

Power

Supply

Power

Supply

Inputs 1-64

Xpt (In=1-128, Out=257-320)

Xpt (In=1-128, Out=385-448)

Xpt (In=1-128, Out=1-64)

Outputs 1-64

Xpt (In=1-128, Out=129-192)

Xpt (In=1-128, Out=193-256)

Outputs 65-128

Xpt (In=1-128, Out=65-128)

Xpt (In=1-128, Out=449-512)

Xpt (In=1-128, Out=321-384)

Inputs 65-128

Matrix Controller 1

Inputs 129-192

Xpt (In=129-256, Out=257-320)

Xpt (In=129-256, Out=385-448)

Xpt (In=129-256, Out=1-64)

Outputs 129-192

Xpt (In=129-256, Out=129-192)

Xpt (In=129-256, Out=193-256)

Outputs 193-256

Xpt (In=129-256, Out=65-128)

Xpt (In=129-256, Out=449-512)

Xpt (In=129-256, Out=321-384)

Inputs 193-256

Matrix Controller 2

Summary of Contents for 7500NB





























































































Search results

Summary of Contents for 7500NB

Reviews:

Related manuals for 7500NB

Brands by name

Popular brands

GRASS VALLEY 7500NB, Instruction Manual

Search results

Summary of Contents for 7500NB

Reviews:

Related manuals for 7500NB

Brands by name

Popular brands