8
TRANSLATION OF
THE ORIGINAL INSTRUCTIONS
BATTERY STAPLER
58G081
ATTENTION: BEFORE USING THE EQUIPMENT, PLEASE
READ THIS MANUAL CAREFULLY AND SAVE THIS FOR
FURTHER USE.
SPECIFIC SAFETY REGULATIONS
Safety warnings for the stapler
•
Always assume that the tool contains staples or other
fasteners.
Careless handling of the stapler can result in
unexpected firing of fasteners and injury.
•
Do not point the tool at yourself or anyone nearby.
An
unexpected launch of the device will result in the fastener
launching, causing injury.
•
Do not start the tool until it is pressed against the
workpiece.
If the tool is not in contact with the workpiece, the
fastener may be reflected from the target.
•
Disconnect the tool from the power source when the
fastener locks in the tool.
When removing a jammed
fastener, the device trigger may be accidentally activated if the
device is connected.
•
Do not use this device to fix electric wires.
It is not
intended for fixing electric wires and may damage the
insulation of electric wires, thus causing electric shock or fire
hazard.
WARNING! The device is used for indoor work.
Despite the use of a safe construction by design, the use of
protective measures and additional protective measures,
there is always a residual risk of injury during work.
Explanation of the pictograms used
1.
Attention! Take special precautions
2.
WARNING Read the instruction manual
3.
Wear protective gloves
4.
Use personal protective equipment (safety goggles, ear
protectors)
5.
Use protective clothing
6.
Remove the battery from the device before performing
any adjustment or cleaning operations.
7.
Keep children away from tools
8.
Protect the device against moisture
CONSTRUCTION AND APPLICATION
The battery stapler is a manual type device. The drive is a DC
motor. This type of power tool is intended for fixing cardboard,
insulating material, fabrics, foil, leather and similar materials to
wooden surfaces or wood-based materials with staples or nails.
The stapler is intended for amateur use only.
WARNING! The stapler is not intended for fixing electric
wires. Do not use the device for purposes other than those
for which it was intended.
DESCRIPTION OF GRAPHIC WEBSITES
The numbering below refers to the device components shown
on the graphic pages of this manual.
1.
Trigger
2.
Depth adjustment knob
3.
Drain
4.
Lighting button
5.
Hammer mode switch
6.
Warning indicator
7.
Magazine
8.
Lighting (LEDs)
9.
Preview pane
10.
Magazine cover
11.
Lock lever
12.
Handle
13.
Beater cover
* There may be differences between the drawing and the
product.
EQUIPMENT AND ACCESSORIES
1.
Hex key - 1 item
PREPARATION TO WORK
CHECKING THE CONTACT MECHANISM
•
Remove all staples or nails from the magazine.
•
Place and press the trigger (
1
) on a piece of wood and
squeeze the trigger (
3
). The trigger and trigger should move
freely.
WARNING! Do not use a power tool if the trigger or trigger
cannot move freely.
•
Place staples or nails in the magazine.
•
Insert the battery into the device.
•
Place and press the trigger (
1
) on the workpiece without
pressing the trigger (
3
) - the device should not work.
•
Release the pressure on the trigger (
1
) (the trigger should
automatically return to its original position).
•
Press the trigger (
3
) - the device should not work (
fig. A
).
WARNING! If the device behaves differently than described
above, do not undertake work and send it to an authorized
service center for repair.
INSERT STITCHES OR NAILS INTO THE MAGAZINE
WARNING! The number of staples or nails left in the
magazine can be read using the preview window (8). If the
magazine has enough staples / nails, the preview window
is transparent. If the number of staples / nails is small or
missing, the preview window will be obstructed in red.
•
Remove the battery from the power tool.
•
Press the lock lever (
11
) and slide out the magazine cover
(
10
) (
fig. B, C
).
•
Place staples / nails on the magazine channel path (
fig.
D
,
E
).
WARNING! Make sure the connectors are positioned
correctly:
The staples are placed on the profiled side of the rail, the staple
crown is located in the upper part of the magazine (the legs are
pointing away from the body of the power tool)
(Fig. D)
.
The nails are placed on the profiled side of the rail, with the
points of the nails pointing downwards
(Fig. E)
.
•
Close the magazine cover (
10
) until the lock lever
(
11
) clicks .
•
Reconnect the battery to the power tool.
WARNING! Do not place fasteners of different lengths. Do
not put staples and nails mixed together.
WARNING! Check that the staples / nails are correctly
placed in the magazine.
WORK / SETTINGS
ON / OFF
WARNING! Make sure the battery is fully charged before
starting work.
