background image

11

how it works

gear 

wheel 

from operator 

drives rack on 

gate

the  sld-24v-d  gate  operator  consists  of  an  electro-mechanical  master 

operator with built in electronic controls and a slave operator for the other 

side that has no electronics of it’s own as it is controlled by the master 

when the operator is activated by remote control or other device, it drives each  

side of the gate open or closed by way of a toothed rack fitted to each gate that 

engages with a gear wheel on each operator.  magnets are fitted to the rack to 

set the close limit of each gate, which is detected by sensors in each operator.  

the open limits are set by way of an encoder in each motor that sends signals 

to the control electronics as to how far each gate has travelled.

the speed of each gate is also constantly monitored by the control electronics 

using  the  encoders  so  if  either  gate  is  obstructed  while  operating  both  will 

reverse direction for safety.

the encoder/magnet system is extremely robust and never needs adjustment.

the master/ slave system keeps each side of the gate in sync, if two single 

operators are used they can get out of sync and don’t have the same level of 

safety.

Summary of Contents for e-Gate SLD-24V-D









































Reviews: