Grandbeing MX1616-310 Operating Instructions Manual Download Page 25

   

 Pag

21

 

z

 

The unit has been dropped or the cabinet damaged. 

2) 

Servicing Personnel: 

Do not attempt to service the unit beyond that 

described in these operating instructions. Refer all other servicing to 
authorized servicing personnel. 

3) 

Replacement parts: 

When parts need replacing ensure the servicer 

uses parts specified by the manufacturer or parts that have the same 
characteristics as the original parts. Unauthorized substitutes may result 
in fire, electric shock, or other hazards. 

4) 

Safety check: 

After repairs or service, ask the servicer to perform safety 

checks to confirm that the unit is in proper working condition. 

 

Mail-In Service 

When shipping the unit, carefully pack and send it prepaid, adequately insured 
and preferably in the original carton. Include a letter detailing the complaint and 
provide a daytime phone and/or email address where you can be reached. 

If repair is needed during the limited warranty period the purchaser will be 
required to furnish a sales receipt/proof of purchase indicating date of 
purchase, amount paid and place of purchase. Customer will be charged for 
the repair of any unit received without such proof of purchase. 

 Warranty 

If your product does not work properly because of a defect in materials or 
workmanship, we (referred to as “the warrantor”) will, for the length of the 
period indicated as below,

 

Parts (1) Year

 Labor(90) Days

which starts 

with the date of original purchase (“Limited Warranty period”), at its option 
either (a) repair your product with new or refurbished parts, or (b) replace it 
with a new or a refurbished product. The decision to repair or replace will be 
made by the warrantor. 

During the “Labor” Limited Warranty period there will be no charge for labor. 
During the “Parts” warranty period, there will be no charge for parts. You must 

Summary of Contents for MX1616-310




























Reviews: