EN
User guide
2
Transport instructions
1. The appliance should only be transported in an
upright position. The packaging must be intact
during transportation.
2. If the appliance has been positioned
horizontally during transportation, it must not be
operated for at least 12 hours to allow the system
to settle.
3. Failure to comply with the above instructions
could result in damage to the appliance for which
the manufacturer will not be held liable.
4. The appliance must be protected against rain,
moisture and other atmospheric influences.
Important
• Avoid touching the bottom of the condenser
metal wires at the back of the appliance while
cleaning or carrying the appliance as you may
receive injuries to your fingers and hands.
• Do not attempt to sit or stand on top of your
appliance as it is not designed for such use. You
could be injured or damage the appliance.
• Make sure that the mains cable is not caught
under the appliance during and after moving it as
this could damage the cable.
• Do not allow children to play with the appliance
or tamper with the controls.
Installation instructions
•
Do not operate your appliance in a room where
the temperature is likely to fall below 10°C. The
appliance may not operate at lower temperatures,
resulting in a reduction in the shelf life of the food.
•
The climate class rate of your appliance is stated
in the Technical Features leaflet and written on the
rating label inside the appliance. It specifies the
appropriate operating ambient temperatures as
explained below.
Climatic class
Ambient temperatures
SN........................... +10 °C to 32 °C
N ............................ +16 °C to 32 °C
ST .......................... +16 °C to 38 °C
T.............................. +16 °C to 43 °C
SN-ST..................... +10 °C to 38 °C
SN-T ...................... +10 °C to 43 °C
Location
Do not place the appliance close to cookers or
radiators or in direct sunlight, as this will cause
extra strain on the appliance's functions.
If this cannot be avoided, the following minimum
space should be maintained:
3 cm from electric stoves
3 cm from heater
• Make sure that sufficient room is provided
around the appliance to ensure free air circulation
(Fig. 3).
Place the spacers at the back of your fridge/freezer
to set the distance between the appliance and the
wall (Fig. 4).
• The appliance should be positioned on a level
surface. The two front legs can be adjusted as
required. To ensure that your appliance is standing
upright adjust the two front legs by turning them
either clockwise or anti-clockwise, until firm contact
is secured with the floor. A correct adjustment of the
two legs prevents excessive vibration and noise
(Fig. 5).
If you want to place two products side by side, e.g.
a refrigerator and a freezer as a side by side
solution you have to use a decoration kit which
contains a small mat and a decoration part. The
mat is mounted on the side of one of the products
to create a space between the products. The
decoration part is placed between the products to
hide the gap between the products (Fig. 3). The
decoration kit is not a part of the product but can
be delivered as an accessory.
Electrical requirements
Warning
This appliance must be earthed.
• Check whether the power type and voltage in
your region corresponds to the one stated on the
rating label inside the appliance.
• The electrical safety of the appliance is only assured
when the earth connection in the house is installed in
accordance with regulations.
• Make sure that the mains cable is not caught
under the appliance during and after moving it, as
this could damage the cable.
• Ensure that the plug remains readily accessible.
Do not connect the fridge/freezer to electronic
energy saving systems which turn off the
electricity as they may damage the product.
Summary of Contents for KF 5326-90 FN
Page 2: ......
Page 6: ...1 2 KF 5326 90 FN KF 5326 90 FN X KF 5356 90 FN KF 5356 90 FN X...
Page 7: ...3 4 5 6 8 7 9 11 10...
