background image

Graham Architectural Products 
Homeowner’s Manual 

 

Acoustical Aluminum Windows 
 

Photo 7 

Activate Top Sash Balance Clip 

Photo 8 

Slide Sash Into Jamb Pocket 

Photo 9 

De-activate Balance Release 

Clip

Push

SERIES 2400 

DOUBLE HUNG WINDOW 

 
 
B.  Interior Top Sash

 

 

1.

 

After the bottom sash is removed, lower the top sash until the balance 

release clips are exposed.  Activate the balance release clips and 
remove the sash as described above in steps two and three 

(Photo 7)

 

C.

 

Exterior Sash 

 

1.  The exterior sash are removed in the same manner as the interior set 

of sash. Follow the steps above for interior sash removal to remove 
the exterior sash also. 

 

Sash Replacement

 

 

 

1.  Insert sash completely into one jamb pocket while holding sash so that 

bottom rail is two (2) inches above the lower end of the sash balance 

(Photo 8)

.  (Top sash must be installed prior to installing the lower 

sash).  

2.

 

Align sash with the other jamb and shift sash into a centered position 
between the jambs. 

3.

 

Carefully lower the sash onto the balances.  The balances should 
support the weight of the sash.   

4.

 

Lower the sash to clear the balance release clips.  De-activate the clip 
by pushing in the bottom of each clip so it is flush with the jamb 

(Photo 9)

5.

 

If balance does not lower with sash (stays up while sash goes down) 

stop process.  

Remove sash and start over at step 1. 

 

Balance Replacement

 

 

1.

 

Remove sash, as described above, to expose the balances located in 
each jamb. 

2.

 

Firmly grip balance housing and pull down to release the balance 
from the clip 

(Photo 10)

.  Continue to hold balance firmly while slowly allowing 

balance to move upward until the hook attaching the balance to the 
jamb is exposed. 
 
 
 
 
 
 
 
 
 

Photo 10 

Grasp And Pull Balance 

Summary of Contents for Series 0400


























Reviews: