background image

S

A F E T Y

2–2

E

MERGENCY

 S

TOP

 S

WITCH

Some Grady-Whites are equipped with an emergency stop switch. This is a safety feature that 

if used properly will shut the engines down if the operator leaves or falls from the helm position. 
The ignition shutdown system includes a shut-off switch, switch clip, lanyard and lanyard clip. 
The lanyard clip is attached to the operator. If a situation arises where the boat should stop, a pull 
on the cord to release the clip from the shut-off switch will shut down the engines. To reset the 
emergency stop switch, simply reinstall the switch clip. The decision to use the emergency stop 
switch rests with the owner/operator. See page 72 in

 Sportfish, Cruisers, Yachts Owner’s Manual.

E

MERGENCY

 I

NFORMATION

While boating, unpleasant situations may develop. You should prepare yourself on how to 

cope with them whether they happen aboard your vessel or someone else’s. Anticipate and game 
plan for specific situations such as fire, man overboard, collision, etc. to give you the confidence 
and ability necessary to handle an emergency. The key is to remain calm. For emergency 
procedures, see Section 4 in 

Sportfish, Cruisers, Yachts Owner’s Manual.

• Rendering Assistance

The owner or operator of a vessel is required by law to render all practical or necessary 
assistance to any person or vessel affected by collision, accident or casualty. 

However, you 

are not required to endanger your vessel or passengers to render assistance.

• Accident Reporting

Report all boating accidents to your local authorities. Federal regulations require boat 
operators involved in an accident to submit a written report within 48 hours.

In the event of 

death or disappearance, notification is required immediately

by phone or radio in addition 

to the written report. These reports can be submitted to the State Boating Law Administrator. 
Forms can be obtained through the USCG, local harbor patrol offices, sheriff, and police 
stations.

• Lightning Precautions

This awareness is included to ensure the safety of the owner and passengers. Always be 
mindful of the weather! When a lightning storm advances, certain safety precautions should 
be taken. Dock the boat and seek shelter on land. If this is not possible, seek refuge inside the 
boat until the storm has passed. 

Stay out of the water!

 Lightning will seek a ground when it 

strikes and may pass through metal components if it hits your boat. For this reason, avoid 
contact with metal parts of the boat under these conditions.

Summary of Contents for TOURNAMENT 225









































































Reviews: