manualshive.com logo in svg

Grady-White Boats Freedom 375, Owner'S Manual, Page: 67 / 86

Share
Download
Grady-White Boats Freedom 375 Owner'S Manual Download Page 67

8-13

Chapter 8: Freedom 375

Freshwater Washdown

To operate the freshwater washdown system, place the “Freshwater” switch on the DC panel in 

the “on” position. This system will now be pressurized at the freshwater outlets. A hose with a spray 
nozzle attached may be used intermittently without turning the switch off in the same fashion as a 
garden hose with a nozzle. The freshwater pump has an internal pressurization switch that will 
maintain water pressure as needed until the switch is turned off.

Generator

The generator enables you to use AC powered accessories without being attached to shore 

power. The diesel generator is a Fischer Panda™ 8 Mini, capable of producing 7500 peak watts** 
(62A) and a constant 6800 watts* (55.8A). The generator diesel fuel is supplied by a separate tank 
located in the aft rigging compartment.

Generator Control Panel

The generator control panel is located in the cabin at the bottom of the AC/DC panel. This panel 

is equipped with some monitoring functions. To learn more about these monitoring functions, 
reference the Fischer Panda owner’s manual included in your Owner’s Packet.

Amperage Requirements

The generator provides sufficient power to operate most accessories at the same time. A list of 

amperage requirements for all AC accessories is provided below. Use the amp meters and volt meter 
on the AC panel to properly manage the load on the generator. The generator is capable of handling 
momentary peaks above its rated capacity. These peaks are normally related to the start-up of each 
accessory. In addition to the factory installed appliances, you should know the amperage 
requirements of any household objects you bring on board.

• 

Air/Cooler Pump 

2.1A 

(1.1A 50Hz) 

Running Amps

• 

Air Conditioner 

8.9A 

(4.5A 50Hz) 

Running Amps

• 

Helm Air Conditioner 

11.7A 

(5.9A 50Hz) 

Running Amps

• 

Battery Charger 

8.0A 

(4.0A 50Hz) 

Maximum Amps

• 

Bow Thruster Charger 

2.0A 

(1.0A 50Hz) 

Maximum Amps

• 

Cockpit Coolers 

6.6A 

(3.3A 50Hz) 

Running Amps

• 

Grill 

10.8A 

(5.4A 50Hz) 

Maximum Amps

• 

Water Heater 

12.5A 

(6.3A 50Hz) 

Maximum Amps

• 

Microwave 

8.75A 

(4.4A 50Hz) 

Maximum Amps

• 

Refrigerator 

4.0A 

(2.0A 50Hz) 

Maximum Amps

Starting the Generator

1.  Ensure the shut-off valve on the diesel fuel tank is open.
2.  Open the generator seacock using the remote seacock arm located in the aft rigging 

compartment and accessed through the aft rigging lid.

3.  Ensure the generator transfer switch and any other load has been switched off.
4.  Press the standby “On/Off” button on the generator control panel. The control light for 

“Standby” must light up.

Summary of Contents for Freedom 375























































































Reviews:

No comments