manualshive.com logo in svg

Grady-White Boats Freedom 307, Owner'S Manual

Share
Download
Grady-White Boats Freedom 307 Owner'S Manual Download Page 57

F

R E E D O M

  3 0 7

8–5

A

UXILIARY

 F

USE

 P

ANEL

There are two auxiliary fuse panels located in the starboard console storage area. The larger of 

the two provides a source of power for factory installed accessories such as the lights and horn. 
The smaller fuse panel is provided for electronics and other non-factory installed accessories. The 
fuse blocks receive power from the positive bus bar. Your model utilizes the automotive type fuse.

A

CCESSORY

 O

UTLET

 - 12 V

OLT

The two 12-volt outlets on your 307 provide easily accessible power supplies for accessories 

such as cellular phones and spotlights. These outlets are located in the port and starboard 
deckwing inserts.

A

NCHOR

 W

INDLASS

The anchor windlass includes a stainless steel bow roller. Please refer to the anchor windlass 

owner’s manual for proper operation of the windlass.

B

ATTERY

 S

ELECT

 S

WITCH

The Freedom 307 is equipped with four batteries and two select switches. The batteries are 

wired into two banks, each bank consisting of two batteries paralled together. An outboard engine 
should be connected to each battery select switch. Either engine may be started with either battery 
bank by selecting position “1” or position “2” on the select switches. In normal use, select 
position “1” on the starboard switch and position “2” on the port switch so that both battery banks 

N O T I C E

These outlets cannot be used with a cigarette lighter.

Summary of Contents for Freedom 307




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands