Graco XP70 Page 31 Instruction & Parts Manual Download

Page: 31 / 56

Troubleshooting

3A0420H

Troubleshooting

✖

Fluid ratio will be wrong.

◆

Purge all air from system before proportioning
fluids.

Problem

Cause

Solution

System stops or will not start.

Air pressure or volume too low.

Increase; check air compressor.

Closed or restricted air line or air
valve.

Open or clean.

Fluid valves closed.

Open.

Clogged fluid hose.

Replace.

Air motor worn or damaged.

Repair air motor; see 311238.

Displacement pump stuck.

Repair pump; see 311762.

System speeds up or runs erratically. Fluid containers are empty.

◆

Check often; keep filled.

Air in fluid lines.

◆

Purge; check connections.

Displacement pump parts worn or
damaged.

Repair pump; see 311762.

Pump operates, but resin output
pressure drops on upstroke.

✖

Dirty, worn, or damaged resin pump
piston valve or piston packings.

Clean, repair pump; see 311762.

Pump operates, but resin output
pressure drops on downstroke.

Dirty, worn, or damaged resin pump
intake valve.

Clean, repair pump; see 311762.

Pump operates, but resin output
pressure drops on both strokes.

✖

Hardener output restriction.

Clean, unplug hardener side. Open
manifold restrictor.

Fluid supply low.

◆

Refill or change container.

Pump operates, but hardener output
pressure drops on upstroke.

✖

Dirty, worn, or damaged hardener
pump piston valve or piston packings.

Clean, repair pump; see 311762.

Pump operates, but hardener output
pressure drops on downstroke.

✖

Dirty, worn, or damaged hardener
pump intake valve.

Clean, repair pump; see 311762.

Pump operates, but hardener output
pressure drops on both strokes.

Resin output restriction.

Clean, unplug resin side.

Fluid supply low.

◆

Refill or change container.

Fluid leak in packing nut.

Loose packing nut or worn throat
packings.

Tighten; replace; see 311762.

Fluid leak under packing nut

Packing cartridge o-ring.

Replace o-ring; see 311762

Relief valve (AM) leaks back to sup-
ply, opens too soon, or will not close.

Relief valve is dirty or damaged.

Replace valve cartridge (302) with kit
262520.

No pressure on hardener side; fluid
leaking from hardener pump outlet
rupture disc fitting.

Overpressure rupture disk blown.

Determine cause of overpressuriza-
tion and correct. Replace rupture disk
assembly (140) and over-pressure
cartridge (302).

Pressure and flow surges on
upstroke.

Feed pressure too high. Every pound
of feed pressure adds 2 psi boost
during upstroke.

Reduce feed pressure. See

Techni-

cal Data

, page 53.

Summary of Contents for XP70

























































Search results

Summary of Contents for XP70

Reviews:

Related manuals for XP70

Brands by name

Popular brands

Graco XP70, Instruction & Parts Manual

Search results

Summary of Contents for XP70

Reviews:

Related manuals for XP70

Brands by name

Popular brands