Graco WB3000 Instructions - Parts Manual Download

Page: 8 / 78

Gun Overview

Controls, Indicators, and Components

The electrostatic gun includes the following

controls, indicators, and components (see Fig.

1). For information on Smart guns, also see

Smart Guns, page 9

Item Description

Purpose

Air Swivel

Inlet

1/4 npsm(m) left-hand

thread, for Graco

red-colored grounded

air supply hose.

Fluid Hose

Graco waterborne ﬂuid

hose

Turbine Air

Exhaust

Barbed ﬁtting, for supplied

exhaust tube.

Air Cap/Tip

Guard and

Spray Tip

See

Spray Tip Selection

Chart, page 71

, for avail-

able sizes.

Electrode

Supplies electrostatic

charge to the ﬂuid.

Item Description

Purpose

Fan Air

Adjustment

Valve

Adjusts fan size and shape.

Can be used to decrease

pattern width.

Atomizing Air

Adjustment

Valve

Adjusts atomizing air ﬂow.

Trigger Safety

Lock

Locks trigger to prevent

gun from spraying.

ES On-Off

Valve

Turns electrostatics ON (I)

or OFF (O).

ES Indica-

tor (standard

gun only; for

Smart gun in-

dicator, see

Operating

Mode, page

)

Lit when ES is ON (I).

Color indicates alternator

frequency. See the LED

indicator table on page 30.

Figure 1 Gun Overview

3A2497C

Summary of Contents for WB3000















































































Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands

Graco WB3000, Instructions - Parts Manual

Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands