Graco WB3000 Instructions - Parts Manual Download Page 74

Page: 74 / 78

Hoses

Grounded Air Hoses

100 psi (0.7 MPa, 7 bar) Maximum Working Pressure

0.315 in. (8 mm) ID; 1/4 npsm(f) x 1/4 npsm(f)

left-hand thread

Part No.

Description

Grounded Air Hose with stainless steel braid

ground path (Red)
235068

6 ft (1.8 m)

235069

15 ft (4.6 m)

235070

25 ft (7.6 m)

235071

36 ft (11 m)

235072

50 ft (15 m)

235073

75 ft (23 m)

235074

100 ft (30.5 m)

Test Equipment

Part No.

Description

241079

Megohmmeter. 500 V output,

0.01–2000 megohms. Use for

ground continuity and gun resistance

tests.Not for use in hazardous areas.

245277

Test Fixture, High Voltage Probe,

and kV Meter. Use to test the

electrostatic voltage of the gun, and

the condition of the alternator and

power supply when being serviced.

See manual 309455.

3A2497C

Summary of Contents for WB3000















































































Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands

Graco WB3000, Instructions - Parts Manual

Search results

Summary of Contents for WB3000

Reviews:

Related manuals for WB3000

Brands by name

Popular brands