Graco True Airless LTS15 Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 56

background image

Start Up

16

3A3529C

3.

Remove outlet valve and clean. Make

certain outlet ball moves free in the

housing.
Install outlet valve and repeat

Flush

Storage Fluid

, page 14.

4.

Remove suction tube. Remove inlet

valve and clean. Make certain the

spring is facing up when the inlet ball

and valve are installed.
Install inlet valve and suction tube and

repeat

Flush Storage Fluid

, page 14.

ProLTS Inlet Valve Removal

An integrated tool is included in the frame to

remove the inlet valve assembly from the

pump. If you suspect that the inlet valve is

clogged or stuck, remove the valve assembly

and clean or replace. Insert pump inlet into

frame and loosen the inlet valve. Remove

inlet valve.

ti30578a

LTS15/LTS17

ti30589a

ProLTS

NOTICE

Do not lose the ball and spring inside the inlet

valve assembly. It may fall out when the inlet

valve is removed. Pump will not prime without

the ball and spring.

ti27479a

«
...
14
15
16
17
18
...
»

Summary of Contents for True Airless LTS15

























































Reviews:

No comments

Related manuals for True Airless LTS15

SPRAY-ON 200 Series

Brand: C-Dax Pages: 10

Brand: P.I.T. Pages: 25

Brand: WAGNER Pages: 12

MEGA VPZ MASTER

Brand: Hardi Pages: 178

Brand: SDI Pages: 2

Brand: F/S Manufacturing Pages: 3

Brand: Graco Pages: 8

Brand: Graco Pages: 56

Brand: Binks Pages: 12

Brand: Graco Pages: 26

Brand: ST Pages: 26

Brand: ST Pages: 43

PRIMA 100 Tolva

Brand: jafe Pages: 16

Flicker Machine

Brand: Faithfull Pages: 2

Brand: Orbit Pages: 16

SPRAY STATION HV3500

Brand: Earlex Pages: 8

Brand: WAGNER Pages: 32

Brand: WAGNER Pages: 130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands