manualshive.com logo in svg

Graco TexSpray HTX 2030, Repair Manual

Share
Download
Graco TexSpray HTX 2030 Repair Manual Download Page 21

Repair

313889B

21

Pump Control

Removal 

1.

Remove two screws (71) and swing cover (70a) 
down.

2.

Disconnect pump control (70p) lead from control 
board (70c).

3.

Loosen set screws on pump control knob (70k) and 
remove knob, shaft nut, lock washer and pump con-
trol (70p).

4.

Remove shaft spacer (70n) from pump control.

Installation

1.

Install shaft spacer (70n) on pump control (70p).

2.

Install pump control, shaft nut, lock washer, and 
pump control knob (70k).

a.

Turn pump control shaft clockwise to internal 

stop. Assemble pump control knob to strike pin 

on cover (70a).

b.

After adjustment of step a, tighten both set 

screws in knob 1/4 to 3/8 turn after contact with 

shaft.

3.

Connect pump control lead to control board (70c).

4.

Swing cover (70a) up and secure with two screws 
(71).

ti13709a

71

71

70a

ti13251a

70p

ti13207a

70k

ti14417a

70n

ti14417a

70p

70n

70k

ti13338a

70k

ti13251a

70p

ti13717a

71

70a

Summary of Contents for TexSpray HTX 2030





























Reviews:

No comments

Brands by name

Popular brands

Load more brands