manualshive.com logo in svg

Graco TexSpray 248091, Operation And Parts

Share
Download
Graco TexSpray 248091 Operation And Parts Download Page 6

Setup 

6

Setup

Grounding

English

Français

Spanish

To reduce risk of electrical shock, proper electric 
grounding is essential. See your sprayer instruction 
manual and consult your local electrical codes for 
detailed grounding instructions.

Installation

1

Relieve Pressure

, page 5. 

2 Connect air and material 

hoses to gun. Tighten securely.

3 If using 

fine finish adapter,

 

install disc (2a) on front of 
adapter (3a) with retaining ring 
(1a). Install a standard 8 mm 
nozzle (4a) on front of gun with 
the assembly. If desired finish 
is not achieved, try a different 
size standard nozzle.
See Nozzle Selection Chart, 
page 7. 

For 

Standard operation

: 

install nozzle (4a) on front of 
gun and secure using retaining 
ring (1a). See Nozzle Selection 
Chart, page 7.

4 Refer to system operation 

manual to start and prime 
sprayer.

1

2

3

4

1

2

3

4

ti4003a

3A

2A

1A

ti4002a

4A

Summary of Contents for TexSpray 248091

























Reviews:

No comments

Brands by name

Popular brands

Load more brands