Graco SDL23 Series Instructions Manual Download

Page: 20 / 54

Installation

3A8626C

Adjust Spring Tension

Single Pedestal SDX Model Hose Reels

Increase Spring Tension

1. Pull the hose out one to two turns, then engage the

latch.

2. Pull the hose back through the hose guides.

3. Wrap a loop of hose onto the reel flange.

4. Check the spring tension. The hose must pull out

fully and retract fully. Wrap more loops, one at a

time around the reel flange, until the spring has the

desired tension.

NOTE: Do not put so many loops onto the reel so that

the spring winds up tightly before the hose is fully

extended.

Decrease Spring Tension

To decrease the spring tension, remove loops around

the reel flange until tension is at the desired level.

Dual Pedestal XDX or XNX Model Hose

Reels

If the hose is not retracting sufficiently, or is wound too

tight, the tension can be increased or decreased using

one of the following procedures:

Increase Spring Tension

(Spring is too loose, hose does not retract

completely, or retraction is sluggish.)

NOTE: The reference letters in the following instructions

refer to F

. 17.

1. Loosen screw (A) three to five turns. Do not

completely remove the screw.

2. Use a hex wrench to loosen the two screws (B). Do

not completely remove the screws.

3. Insert a 3/8 in. square drive breaker bar into

opening (C) on the spring adjustment plate (D).

4. While holding the breaker bar securely, completely

remove the two screws (B).

5. While firmly grasping the breaker bar with both

hands, turn the spring adjustment plate clockwise

one turn at a time to increase (tighten) the spring

tension.

6. Replace and finger-tighten both screws (B).

7. Remove the breaker bar.

SPRING TENSION HAZARD

The hose reel spring is always under great tension,

which if released in an uncontrolled manner could

cause serious injury.
• Never allow the reel to spin freely. Uncontrolled

spinning could cause serious injury if hit by the

hose.

• Always grasp the adjusting tool firmly with both

hands when adjusting tension. Spring tension

can cause the tool to move violently.

• Securely fasten the reel in place while making

adjustments.

• The hose reel spring is not a serviceable part. Do

not attempt to replace or service the hose reel

spring.

• Always wear heavy gloves while adjusting the

spring tension to protect your hands from being

cut on the hose reel.

. 17

Summary of Contents for SDL23 Series























































Search results

Summary of Contents for SDL23 Series

Reviews:

Related manuals for SDL23 Series

Brands by name

Popular brands

Graco SDL23 Series, Instructions Manual

Search results

Summary of Contents for SDL23 Series

Reviews:

Related manuals for SDL23 Series

Brands by name

Popular brands