background image

Double Ball Service

Double Ball Service

Disconnect the Pump

WARNING

PRESSURIZED FLUID HAZARD
This equipment stays pressurized until pressure is

relieved manually. To help prevent serious injury

from moving parts, or from pressurized fluid, such

as splashing in the eyes or on skin, follow the

Pressure Relief Procedure in your system manual

when you stop pumping and before you clean,

check, or service the equipment.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when

in the work area to help prevent serious injury,

including eye injury, hearing loss, or inhalation of

toxic fumes.

This procedure involves thoroughly disassembling

and cleaning the individual parts in the pump lower

unit. Prior to performing this procedure, flush the

pump and relieve pressure as described in the

system manuals, disconnect all hoses, and remove

the pump from the system.
1. Hold the reducer fitting with a wrench. Use a

spanner wrench (T)* to loosen the coupling nut.
* A Graco spanner wrench tool (112887) is

available.

2. Lower the coupling nut enough to remove the

coupling collars.

3. Release the clamp (C) holding the displacement

pump (L) to the tie rod plate (P).

6

3A5798B

Summary of Contents for SaniForce 5:1





















Reviews: