background image

Graco

Graco

Graco Standard

Standard

Standard Warranty

Warranty

Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be
free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception
of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the
date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies
only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage
or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance,
negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall Graco be liable for
malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories,
equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized
Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace

free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid.
If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a
reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS

THIS

THIS WARRANTY

WARRANTY

WARRANTY IS

IS

IS EXCLUSIVE,

EXCLUSIVE,

EXCLUSIVE, AND

AND

AND IS

IS

IS IN

IN

IN LIEU

LIEU

LIEU OF

OF

OF ANY

ANY

ANY OTHER

OTHER

OTHER WARRANTIES,

WARRANTIES,

WARRANTIES, EXPRESS

EXPRESS

EXPRESS OR

OR

OR IMPLIED,

IMPLIED,

IMPLIED,

INCLUDING

INCLUDING

INCLUDING BUT

BUT

BUT NOT

NOT

NOT LIMITED

LIMITED

LIMITED TO

TO

TO WARRANTY

WARRANTY

WARRANTY OF

OF

OF MERCHANTABILITY

MERCHANTABILITY

MERCHANTABILITY OR

OR

OR WARRANTY

WARRANTY

WARRANTY OF

OF

OF FITNESS

FITNESS

FITNESS FOR

FOR

FOR A

A

A

PARTICULAR

PARTICULAR

PARTICULAR PURPOSE.

PURPOSE.

PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer
agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost
sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for
breach of warranty must be brought within two (2) years of the date of sale.

GRACO

GRACO

GRACO MAKES

MAKES

MAKES NO

NO

NO WARRANTY,

WARRANTY,

WARRANTY, AND

AND

AND DISCLAIMS

DISCLAIMS

DISCLAIMS ALL

ALL

ALL IMPLIED

IMPLIED

IMPLIED WARRANTIES

WARRANTIES

WARRANTIES OF

OF

OF MERCHANTABILITY

MERCHANTABILITY

MERCHANTABILITY AND

AND

AND

FITNESS

FITNESS

FITNESS FOR

FOR

FOR A

A

A PARTICULAR

PARTICULAR

PARTICULAR PURPOSE,

PURPOSE,

PURPOSE, IN

IN

IN CONNECTION

CONNECTION

CONNECTION WITH

WITH

WITH ACCESSORIES,

ACCESSORIES,

ACCESSORIES, EQUIPMENT,

EQUIPMENT,

EQUIPMENT, MATERIALS

MATERIALS

MATERIALS

OR

OR

OR COMPONENTS

COMPONENTS

COMPONENTS SOLD

SOLD

SOLD BUT

BUT

BUT NOT

NOT

NOT MANUFACTURED

MANUFACTURED

MANUFACTURED BY

BY

BY GRACO

GRACO

GRACO. These items sold, but not manufactured by

Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco
will provide purchaser with reasonable assistance in making any claim for breach of these warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco
supplying equipment hereunder, or the furnishing, performance, or use of any products or other goods sold hereto,
whether due to a breach of contract, breach of warranty, the negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and

legal proceedings entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn
up in English. Les parties reconnaissent avoir convenu que la rédaction du présente document sera en Anglais,
ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite de ou en rapport,
directement ou indirectement, avec les procédures concernées.

Graco

Graco

Graco Information

Information

Information

For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.

To

To

To place

place

place an

an

an order,

order,

order, contact your Graco Distributor or call to identify the nearest distributor.

Phone:

Phone:

Phone: 612-623-6921 or

or

or Toll

Toll

Toll Free:

Free:

Free: 1-800-328-0211 Fax:

Fax:

Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original Instructions. This manual contains English. MM 3A6781

Graco

Graco

Graco Headquarters:

Headquarters:

Headquarters:

Minneapolis

International

International

International Offices:

Offices:

Offices: Belgium, China, Japan, Korea

GRACO

GRACO

GRACO INC.

INC.

INC. AND

AND

AND SUBSIDIARIES

SUBSIDIARIES

SUBSIDIARIES ••• P.O.

P.O.

P.O. BOX

BOX

BOX 1441

1441

1441 ••• MINNEAPOLIS

MINNEAPOLIS

MINNEAPOLIS MN

MN

MN 55440-1441

55440-1441

55440-1441 ••• USA

USA

USA

Copyright

Copyright

Copyright 2019,

2019,

2019, Graco

Graco

Graco Inc.

Inc.

Inc. All

All

All Graco

Graco

Graco manufacturing

manufacturing

manufacturing locations

locations

locations are

are

are registered

registered

registered to

to

to ISO

ISO

ISO 9001.

9001.

9001.

www.graco.com

Revision D, January 2021

Summary of Contents for saniforce 1590

































Reviews: