background image

Repair

Overmolded

Overmolded

Overmolded Diaphragm

Diaphragm

Diaphragm Repair

Repair

Repair

Tools

Tools

Tools Required

Required

Required

• Torque wrench

• 19 mm open end wrench

• O-ring pick

• Lithium base grease

Disassemble

Disassemble

Disassemble the

the

the Overmolded

Overmolded

Overmolded Diaphragms

Diaphragms

Diaphragms

NOTE:

NOTE:

NOTE: Diaphragm kits are available in a range of
materials and styles. See Parts section.

1.

Follow the

Pressure Relief Procedure, page 9

.

2.

Remove the manifolds and disassemble
the check valves as explained in

Check Valve Repair, page 12

.

3.

Remove the clamps (21) from the fluid covers
(15), then pull the fluid covers off of the pump.

4.

Once the fluid covers are removed, the
diaphragm on the side of the pump which was
last pressurized with air will be separated from
the center section/air cover. This allows you to
grip the diaphragms.

5.

To loosen, grip both diaphragms securely around
the outer edge and rotate counterclockwise. One
diaphragm assembly will come free and the other
will remain attached to the shaft. Remove the
freed diaphragm (10), screw (14) if it remains in
the shaft, and air side plate (9).

6.

Pull the opposite diaphragm assembly and shaft
(24) out of the center housing (101). Hold the
shaft flats with a 19 mm open end wrench and
remove the diaphragm and air side plate from
the shaft.

7.

Inspect the diaphragm shaft (24) for wear or
scratches. If it is damaged, inspect the bearings
(111) in place. If the bearings are damaged, refer
to

Center Section Repair, page 17

.

8.

Reach into the center housing (101) with an
o-ring pick and hook the u-cups (110), then pull
them out of the housing. This can be done with
the bearings (111) in place.

9.

Clean all parts and inspect for wear or damage.
Replace parts as needed.

3A6780C

15

Tel:  866-777-6060 
Fax: 866-777-6383

Springer Pumps, LLC

Website: www.springerpumps.com 

Int'l: +001 267 404 2910

Summary of Contents for SaniForce 1040



























Reviews: