background image

Repair

313221A

47

Electric Motor

Test Motor

If motor is not locked up by pumps, it can be 
tested using a 9 V battery. Open recirculating 
valves, disconnect J4 or J11 from control 
board, see F

IG

. 12, page 43. Touch jumpers 

from battery to motor connections. Motor 
should turn slowly and smoothly.

Removal

2. Remove four screws (207) and shroud 

(206). See F

IG

. 14.

3. Remove drive housing/pump assemblies, 

page 45.

4. Disconnect motor cables as follows:

a. Find control board at back of control 

module, see F

IG

. 12, page 43. 

b. Unplug motor power connector from 

J11 (120 V units).

c. Unplug motor temp switch harness from 

connector J7. 

d. Unplug cable (37) from fan (202). See 

F

IG

. 18.

e. Thread motor power switch harness out 

bottom of control module and cable 
channel, to free motor.

5. Remove screws holding motor to bracket. 

Lift motor off unit.

Installation

1. If replacing motor, install fan assembly and 

fan mount threaded bushing on new motor.

2. Place motor and fan on unit. Thread motor 

switch harness into control module.

3. Fasten motor with screws underneath. Do 

not tighten yet.

4. Plug 3-pin connector J7 to board.

5. Plug Motor Power switch harness to con-

nector J11 (120 V units).

6. Install drive housing/pump assemblies, 

page 45. Reconnect inlet assemblies to 
pumps.

7. Tighten motor mounting screws.

8. Return to service.

If replacing a component with electrical 
cabling, remove one supply tank, page 
36. 

1. See Before Beginning Repair, page 35. 

Relieve pressure, page 22.

CAUTION

Motor is heavy. Two people may be required 
to lift.

Summary of Contents for Reactor E-10





























































Reviews: