background image

Maintenance 

14

3A6831G

Maintenance

Preventive Maintenance 
Schedule

The operating conditions of your particular pump deter-
mines how often maintenance is required. Establish a 
preventive maintenance schedule by recording when 
and what kind of maintenance is needed, and then 
determine a regular schedule for checking your pump.

Tighten Threaded Connections

Check that all threaded connections are tight before 
each use and at routine intervals.

Tighten Packings

The packings included in your pump have the ability to 
be adjusted to stop leaks that develop when the seals 
are worn. If a leak develops in the pump’s fluid section, 
tighten the packing nut clockwise by 1/16 of a turn, or 
lower, until the leak is eliminated. The life of the packing 
can be affected by over-tightening the packings. If the 
packing nut needs to be tightened repeatedly after short 
intervals, replace the packing.

Storage

If the pump is going to be stored for long periods, flush 
the pump with a light-weight oil or rust prohibiter before 
storage to protect pump components. Store the pump 
with protective fluid inside whenever possible.

Summary of Contents for Python XL-DA25 Series













































Reviews: